Integrated Motor vs. Traditional Motor: Structure, Wiring and Cost Compared (2026)

3 views

An integrated motor puts the driver, encoder, controller and I/O module inside the motor housing; a traditional motor needs a separate driver and controller. The difference goes beyond size — wiring, commissioning, multi-axis scaling and maintenance granularity all change. Which one to choose depends on your axis count, cabinet space, load profile and budget structure, not on which is "more advanced."

1. From a three-piece set to an all-in-one unit

A traditional setup is a three-piece set: the motor mounts on the machine, the driver sits in the control cabinet, and the controller takes up another slot — all three connected by power and signal cables.

An integrated motor brings these parts into a single housing. In Limaisheng (NiMotion) integrated stepper motors, for example, the stepper motor, driver, encoder, controller and I/O module are integrated into one unit, with operating data, parameter settings and motion commands all handled over the network. The cabinet then only needs to supply power and communication, with no separate driver slot per axis.

Table: Components — traditional vs. integrated motor

Component

Traditional motor

Integrated motor

Motor

Mounted on the machine

Mounted on the machine

Driver

Separate cabinet unit, one per axis

Inside the motor housing

Encoder

At the rear of the motor, separately wired

Inside the housing

Controller / motion control

Standalone controller or PLC motion module

Inside the housing; host issues commands

I/O

Separate I/O module or terminals

Inside the housing

Cabinet footprint

One driver slot per axis plus wiring space

No driver slots; power and communication only

2. Six dimensions compared

Table: Integrated vs. traditional motor across six dimensions

Dimension

Traditional motor

Integrated motor

Cabinet space

Drivers take slots; grows with axis count

No driver slots; does not grow linearly with axes

Cabling

Motor, encoder and control cables, multiple runs

Concentrated power and communication cabling

Commissioning

Driver parameters and controller configured separately

Parameters sent over the network, online monitoring

Multi-axis scaling

Each new axis needs another driver and cabinet space

Add a motor per axis; suited to distributed architectures

Maintenance granularity

Motor and driver replaceable separately

Unit-level replacement; single-axis fault affects one axis

Cost structure

Lower unit cost, but cabinet, cabling and assembly add up

Higher unit cost, saves cabinet, cabling and assembly

3. Space and wiring: where the savings come from

In a traditional setup the cabinet must reserve a slot per driver, plus cooling clearance and cable ducts. With many axes, cabinet size is often driven by driver count rather than by actual control requirements.

An integrated motor moves the driver into the motor housing, leaving only power and communication in the cabinet. Limaisheng describes its integrated stepper motors as compact, efficient and space-saving, with considerable installation space saved compared with a conventional motor combination — the savings are mainly cabinet driver space and inter-cabinet cabling.

Note that the space advantage is at the system level, not the unit level: a single integrated motor is usually somewhat longer than a standard motor of the same frame, because it carries the driver and encoder. What you save is the cabinet and the wiring, not the motor itself.

4. Commissioning and scaling: the gap widens with axis count

With a few axes, the two approaches are not very different — a matter of a few cables. At ten or dozens of axes, the difference becomes significant.

In a traditional setup each driver is configured individually; commissioning means wiring and parameterising them one by one. With integrated motors, the controller only issues commands and monitors status rather than communicating with each motor every control cycle, so CPU load and bus load stay lower and more axes can be driven. Limaisheng states that the controller no longer needs to communicate with the motor every control cycle, greatly reducing CPU usage and bus load so more motors can be controlled.

Limaisheng integrated stepper motors support CAN, CANopen, RS485 and RS232, with CiA402 control modes: Profile Position (PP), Profile Velocity (PV), Profile Torque (PT) and Homing (HM). The communication field in the model code states the interface — in STM 57 56 A - 485 - H - 0 F S B, for example, 485 means RS485.

5. Cost is not just unit price

Compared on unit price alone, the traditional approach is usually cheaper. But total cost also includes cabinet size and enclosure cost, driver installation labour, cable and harness fabrication, wiring and troubleshooting time, and future maintenance diagnostics.

These costs scale with axis count. The more axes, the more the integrated approach wins on total cost; for single-axis or two-to-three-axis machines, the traditional approach can be more economical.

6. When a traditional motor is the better choice

  • Single-axis or very low axis count, with cabinet space available

  • High-power, heavy-duty transmission needing a large external driver with its own cooling

  • Requirement to replace drivers individually — fine maintenance granularity

  • An established cabinet-drive architecture and spare-parts system you do not want to change

7. When an integrated motor is the better choice

  • Tight cabinet space, or a need to shrink overall machine size

  • Distributed multi-axis architectures where fewer cables and connection points matter

  • Space-sensitive equipment in medical testing, biotechnology and 3C electronics

  • Linear motion requirements, where integrated lead-screw stepper motors remove the coupling and extra structural parts

  • Special environments needing IP65 protection or wide-temperature operation

8. FAQ

Q1: Is an integrated motor just a driver stuffed into a motor?
Structurally, yes — but the impact is wider. Once the driver is inside, wiring, parameter delivery, multi-axis scaling and maintenance all change.

Q2: Is an integrated motor always cheaper?
No. Unit price is usually higher, but cabinet, cabling and assembly are saved. The more axes, the stronger the total-cost case; with very few axes the traditional approach may win.

Q3: Does an integrated motor run hotter?
The driver sits close to the motor body, concentrating heat sources. Confirm duty cycle and ambient temperature during selection, and choose a wide-temperature model if needed.

Q4: If one unit fails, does the whole axis need replacing?
Maintenance granularity is unit-level. A single-axis fault means replacing that motor without affecting other axes, but the replacement cost is higher than swapping a driver.

Q5: What communication options are supported?
Limaisheng integrated stepper motors support CAN, CANopen, RS485 and RS232; the communication field in the model code identifies the interface.

Related reading: "Integrated Servo vs. Traditional Servo" applies the same comparison to the servo family.

Share to:

Need Expert Support?

Our engineering team is ready to provide customized motion control solutions.